Martin MAC 600E Manual de usuario

MAC 600 (E) NTuser manual

10MAC 600 (E) NTRIGGING6The MAC 600 (E) NT can be placed directly on the stage floor or rigged in any orientation on a truss. The integratedFast-Lock

Fixture settings 11FIXTURE SETTINGS7The LED control panel is used to set the address and personalities, read lamp hours and other information, calibra

12MAC 600 (E) NTDMX mode and addressThe DMX mode options are described under “DMX-512 control” on page 20. Maximum flexibility is provided inmode 4.

Fixture settings 13Personality settings* Setting may be overridden via DMX. See the protocol for details.Personality Path Options Effect (Default sett

14MAC 600 (E) NTTests and readoutsThe following readouts and tests are available from the control panel. To calibrate temperature sensorsThe temperat

Fixture settings 15Manual controlThe manual control menu provides limited operation from the control panel. Function Path Options Effect ResetMAN/ RST

16MAC 600 (E) NTAdjustment control The adjustment menu provides manual control for making mechanical adjustments. These shall be performed by aqualif

Fixture settings 17UtilitiesCALIBRATIONThe calibration function allows you to fine-tune effect positions for uniformity between fixtures. Using one fi

18MAC 600 (E) NTOPTICAL CONFIGURATIONS8Field anglesNarrow and wide angle options are available for the MAC 600 (E) NT. The optional lenses are mounte

Optical configurations 19SnootThe snoot may be installed to reduce light spill to the sides. To install the snoot 1 Bend the tabs 90°.2 Bend the ring

© 2000 Martin Professional A/S, Denmark.All rights reserved. No part of this manual may bereproduced, in any form or by any means, withoutpermission i

20MAC 600 (E) NTOPERATION9DMX-512 controlThe MAC 600 (E) NT may be controlled with any DMX-512 controller. Four DMX modes are available that provided

Operation 21The lamp can be turned off from the controller. The DMX lamp off command is executed if DMX lamp off (SPEC/dLof) is set to ON. Note: It is

22MAC 600 (E) NTBEAM SHAPERThe beam shaper widens the beam on one axis and flattens it on the other. The effect rotates 180°. The Shortcuts(SPEC/SCUT

Updating software 23UPDATING SOFTWARE10The latest software and documentation for the MAC 600 (E) NT is available from the Martin Professional web site

24MAC 600 (E) NTFIXTURE SERVICE11Excessive dust, grease, and smoke fluid buildup can result in damage that is not covered by the warranty. Dirty lens

DMX protocol 25DMX PROTOCOLADMX channel Start code = 0DMX1 DMX2 DMX3 DMX4 Value Percent Function1Note:Lamp Off is allowed with SPEC/dLoF set to ON, or

26MAC 600 (E) NT-13-130 - 255 0 - 100Tilt Fine (16-bit LSB)Up down- - 12 140 - 2 3 - 245246 - 248249 - 251252 - 2550 - 11 - 9696 - 9798 - 9899 - 100

Display messages 27DISPLAY MESSAGESBDisplay readout Appears if... What to doSRST (Serial reset)...the fixture receives a reset command from the contro

28MAC 600 (E) NTTROUBLESHOOTINGCProblem Probable cause(s) RemedyOne or more of the fixtures is completely dead.Fixture not powered on.Check that powe

Circuit board connections 29CIRCUIT BOARD CONNECTIONSDOPTO2OPTO1To display panelRedXLR polarity jumperTo transformerFANTo base fanCTCDIMCYANMAGYELCOLO

INTRODUCTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4SAFETY . . . . .

30MAC 600 (E) NTSPECIFICATIONSEMEASUREMENTSDimensions (LxWxH) without clamps . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Specifications 31THERMALMaximum ambient temperature. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

fastslowT PAN/TILT SPEED210 20 30 40 50 60 70 80 90 closed openSTROBE RANDOM STROBEmed slowRESET LAMPON SHUTTERfastLAMPOFF*← *> 5 sec.MODETEFFECTS

4MAC 600 (E) NTINTRODUCTION1The MAC 600 NT is a highly efficient automated 575 watt moving-head wash light that features subtractive cyan,magenta, an

Safety 5SAFETY2Warning! This product is for professional use only. It is not for household use.This product presents risks of lethal or severe injury

6MAC 600 (E) NTAC POWER3WARNING! For protection from dangerous electric shock, the fixture must be grounded (earthed). The AC mains supply shall be

AC power 7Power connectionYou may need to install a cord cap that fits your supply on the power cable. A 3-prong grounding-type plug must beinstalled

8MAC 600 (E) NTLAMP4Compatible lampsThe MAC 600 (E) NT shall be used only with the lamps listed on page 30. Installing any other lamp may damage thef

Data connection 9DATA CONNECTION5The MAC 600 (E) NT has locking 3-pin data input and output sockets that are compatible with DMX 512 devices, i.e.,pin