Martin MAC Viper AirFX Guía de usuario

MAC Viper™ ProfileUSER GUIDE

10 MAC Viper Profile User GuideBreakup and aerial gobosThe breakup and aerial wheels in the MAC Viper Profile each provide 5 rotating gobos plus an o

Control panel operations 11Control panel operationsYou can configure individual fixture settings (such as the MAC Viper Profile’s DMX address), read

12 MAC Viper Profile User GuideTo activate the display when the fixture is not connected to power, press the Escape button. The display extinguishes

Control panel operations 131. Click the jog wheel to enter the main menu.2. Rotate the jog wheel to scroll down to CONTROL MODE, then click the jog w

14 MAC Viper Profile User Guide• EFFECT SHORTCUT determines whether the gobo wheels and color wheel take the shortest path between two positions (sho

Control panel operations 15QUALITY displays the quality of the received DMX data as a percentage of packets received. Values much below 100 indicate

16 MAC Viper Profile User GuideAdjusting settings via DMXCertain fixture settings and parameters can be adjusted from the DMX controller on the fixtu

RDM 17RDMThe MAC Viper Profile can communicate using RDM (Remote Device Management) in accordance with ESTA’s American National Standard E1.20-2006:

18 MAC Viper Profile User GuideSoftware service functionsService utilitiesThe control panel SERVICE menu provides utilities for technicians rigging o

Software service functions 19Firmware installationThe currently installed firmware (fixture software) version can be viewed in the control panel INFO

© 2012 Martin Professional A/S. Information subject to change without notice. Martin Professional A/S and all affiliated companies disclaim liability

20 MAC Viper Profile User GuideDMX protocolApplicable when running MAC Viper Profile firmware version: 1.0.0Basic 16-bit Mode16-bit Extended ModeDMX

DMX protocol 217801 - 141516 - 293031 - 444546 - 596061 - 747576 - 899091 - 104105106 - 119120121 - 134135 - 140141 - 145146 - 150151 - 155156 - 1601

22 MAC Viper Profile User Guide890 - 910 - 1415 - 1920 - 2425 - 2930 - 3435 - 3940 - 4445 - 4950 - 5455 - 5960 - 8990 - 119120 - 149150 - 179180 - 20

DMX protocol 2311 120 - 910 - 1415 - 1920 - 2425 - 2930 - 3435 - 3940 - 4445 - 4950 - 5455 - 5960 - 8990 - 119120 - 149150 - 179180 - 209210 - 232233

24 MAC Viper Profile User Guide14 1501 - 91011 - 192021 - 293031 - 394041 - 495051 - 596061 - 697071 - 798081 - 899091 - 99100 - 110111 - 115116 - 12

DMX protocol 2518 190 - 2550 - 23 - 126127 - 129130 - 253254 - 2550 - 10001 - 505152 - 99100Prism indexing angle, rotation speed and directionIf pris

26 MAC Viper Profile User Guide26 290 - 910 - 1415 - 1920 - 2425 - 2930 - 3435 - 3940 - 4445 - 4950 - 5455 - 5960 - 6465 - 6970 - 7475 - 7980 - 8485

DMX protocol 27MSB = Most significant byteLSB = Least significant byte-31Reserved for future use-32Reserved for future use-33Reserved for future use-

28 MAC Viper Profile User GuideControl panel menusApplicable when running firmware version 1.0.0Menus marked* are available only when the fixture is

Control panel menus 29PERSONALITY(continued)AUTO LAMP ONOFF Automatic lamp striking disabledONLamp strikes automatically within 90 seconds of fixture

ContentsIntroduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

30 MAC Viper Profile User GuideDMX LIVE* RATE 0 - 44 HZDMX transmission speed in packets per secondQUALITY 0 - 100% Percent of packets received START

Control panel menus 31MANUAL CONTROL(continued)*PAN 0 - 255 Set pan angle (default = 128)PAN FINE 0 - 255 Set pan angle, fine (LSB, default = 128)TIL

32 MAC Viper Profile User GuideService and display messagesThe MAC Viper Profile gives service and maintenance information by displaying a large 3- o

www.martin.com • Olof Palmes Allé 18 • 8200 Aarhus N • DenmarkTel: +45 8740 0000 • Fax +45 8740 0010

MAC Viper™ ProfileSAFETY AND INSTALLATION MANUAL

DimensionsAll measurements are given in millimetersThis minimum center-to-center distance can be reduced if pan limits are set via the control menus55

ContentsSafety Information. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Safety InformationThe following symbols are used to identify important safety information on the product and in this document:Warning! The MAC Viper P

Safety Information 5America the cable must be 12 AWG minimum conductor size, SJT or better. In the EU the cable must be 2.5 mm², HAR compliant.• Befo

6 MAC Viper Profile Safety and Installation GuideIntroductionThank you for selecting the Martin™ MAC Viper Profile™. This moving-head spotlight featu

4 MAC Viper Profile User GuideIntroductionThis User Guide is a supplement to the Installation and Safety Manual that is supplied with the MAC Viper P

Introduction 7PackingImportant! Release the tilt lock and allow the fixture to cool before packing it in its flightcase.The anti-shock material in th

8 MAC Viper Profile Safety and Installation GuidePhysical installationWarning! The MAC Viper Profile has a powerful pan motor. The torque reaction wh

Physical installation 9Clamping the fixture on a truss1. Check that the rigging clamps are undamaged and can bear at least 10 times the weight of the

10 MAC Viper Profile Safety and Installation Guide6. See Figure 6. Install a safety wire that is approved as a safety attachment for the weight of th

AC power 11AC powerWarning! For protection from electric shock, the fixture must be electrically connected to ground (earth). The AC mains power supp

12 MAC Viper Profile Safety and Installation GuideConnecting to an AC mains power sourceThe MAC Viper Profile power cable can be hard-wired to a buil

DMX data link 13DMX data linkThe MAC Viper Profile has 5-pin locking XLR sockets for DMX and RDM input and output (see Figure 7 on page 12). The defa

14 MAC Viper Profile Safety and Installation GuideService and maintenanceWarning! Read “Safety Information” on page 4 before servicing the MAC Viper

Service and maintenance 15Lamp lifeMonitor lamp hours using the resettable LAMP ON TIME counter in the INFORMATION control menu. To reduce the risk o

16 MAC Viper Profile Safety and Installation Guide6. Close the lamp access cover and tighten the screw to secure the cover before reapplying power.7.

Effects 5EffectsThis section gives details of the effects that can be controlled via DMX. See the DMX protocol table on page 20 for details of the ch

Service and maintenance 17Access to the headWarning! Disconnect from power and allow to cool for 30 minutes before opening the head.To open the head:

18 MAC Viper Profile Safety and Installation Guide• Airborne dust (from stage effects, building structures and fittings or the natural environment at

Service and maintenance 197. Remove the old air filter element from the filter housing and put the new element into position with the ribs in the ele

20 MAC Viper Profile Safety and Installation GuideLubricationThe MAC Viper Profile does not require lubrication under normal circumstances. The slide

Service and maintenance 21Gobos: generalThe MAC Viper Profile uses specially designed borosilicate 3.3 gobos with a heavy matted aluminum coating tha

22 MAC Viper Profile Safety and Installation GuideGobo handling and storage1. Store all gobos in a dust-free environment with approx. 50% humidity.2.

Service and maintenance 235. See Figure 19. Grasp the goboholder by its teeth and pull it out of its clip to remove it from the wheel. 6. Note that t

24 MAC Viper Profile Safety and Installation GuideReplacing a color filterThe MAC Viper Profile has eight dichroic color filters. See the MAC Viper P

Service and maintenance 25Replacing the FX wheelMAC Viper Profile has a motorized FX wheel that provides gobo animation effects and integrated gobos.

26 MAC Viper Profile Safety and Installation Guide4. Loosen the two Torx 20 screws E to release the projection module.5. See Figure 25. Lift the proj

6 MAC Viper Profile User GuideFX wheel controlThe FX wheel uses two DMX channels:• On the first channel, you set the FX wheel position or select a mo

Service and maintenance 277. See Figure 27. Use a small flat-headed screwdriver to lever the retaining circlip A away from the FX wheel hub to releas

28 MAC Viper Profile Safety and Installation GuideUsing the fixtureBefore using the fixture, download and read the latest version of the MAC Viper Pr

Troubleshooting 29Troubleshooting Problem Probable cause(s) RemedyOne or more of the fixtures is completely dead.No power to fixture.Check that power

30 MAC Viper Profile Safety and Installation GuideSpecificationsPhysicalLength (base). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Specifications 31InstallationMounting points . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Eight 1/4-turn locking points, octa

32 MAC Viper Profile Safety and Installation GuideOrdering informationMAC Viper Profile™ in cardboard packing case . . . . . . . . . . . . . . . . .

www.martin.com • Olof Palmes Allé 18 • 8200 Aarhus N • DenmarkTel: +45 8740 0000 • Fax +45 8740 0010

Effects 7Beam effect (rotating prism)The four-facet prism can be applied at indexed angles or rotated with variable direction and speed.IrisThe iris

8 MAC Viper Profile User GuideOptical configurationPrismThe MAC Viper Profile is supplied with an interchangeable four-facet 15° rotating prism (P/N

Optical configuration 9FX wheelThe MAC Viper Profile is supplied with the “Super Sic 58” FX wheel (P/N 43950059) installed. This wheel has an animati