Martin MX SERIES Manual de usuario Pagina 1

MX-4user manual

10Stand-alone operationSTAND-ALONE OPERATION4 CUSTOM SETTINGSStand-alone operation may be customized with the settings in Table 3. The optionsmay be c

Stand-alone operation11not strike, disconnect the fixture from power for several minutes to reduce strain onthe starter while the lamp cools. MASTER

12MC-1 operationMC-1 OPERATION5The MX-4 is fully compatible with the Martin MC-1 Controller. See the MC-1 usermanual for additional information. SETTI

DMX operation13DMX OPERATION6This section describes how to set up and connect the MX-4 for operation with DMXcontrollers. DATA CONNECTIONA reliable d

14DMX operationTo connect the data link1 Connect a data cable to the controller’s data output. If the controller has a 5-pinoutput, use a 5-pin male t

DMX operation15 6/7 CHANNEL DMX OPERATION The 6-channel DMX mode provides position control of all effects plus speedcontrol of the moving mirror. The

16DMX operationTo select DMX mode1 Disconnect the fixture from power. Set DIP-switch pin 10 to OFF.2 To select 1-channel DMX mode, set DIP-switch pin

DMX operation17DIP-Switch Setting0 = OFF1 = ON#90000000011111111#80000111100001111#70011001100110011#60101010101010101#1 #2 #3 #4 #500000 326496128160

18LampLAMP7 COMPATIBLE LAMPSThe MX-4 uses the Philips CDM-SA/T (short-arc, tubular) 150W discharge lamp.If desired, the GE Arcstream 150 may be substi

Lamp19To orient the Arcstream lamp for maximum lifeIf using the GE Arcstream lamp, maximum lamp life will be achieved by installingthe lamp so that th

21 focus lens2 cover bolts3 air vent4 mirror assembly5 pan/tilt arm6 safety cable holes7 mounting bracket8 air vents9 AC input & main fuse10 DIP-s

20Basic serviceBASIC SERVICE8The MX-4 requires simple routine maintenance. The maintenance scheduledepends heavily on the operating environment; pleas

Basic service21To clean the fan and air ventsTo maintain adequate cooling, dust must be cleaned from the fan and air ventsperiodically.1 Remove the da

22TroubleshootingTROUBLESHOOTING9Problem Probable cause(s) RemedyOne or more of the fixtures is completely dead.No power to fixture.Check that power i

DMX protocol23DMX PROTOCOLAChannel Value Percent Function10 - 910 - 1920 - 99100 - 159160 - 179180 - 204205 - 229230 - 239240 - 249250 - 2550 - 33 - 7

24DMX protocol30 - 1112 - 2324 - 3536 - 4748 - 5960 - 7172 - 8384 - 9596 - 107108 - 119120 - 131132 - 143144 - 155156 - 167168 - 179180 - 191192 - 203

Specifications25SPECIFICATIONSBPHYSICALSize (L x W x H) ... 537 x 269 x 263 mm (21.1 x 10.6 x 10.4 in)

3INTRODUCTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4AC POWER . . . . . . . . . . . . . . . . . . . . . . .

4IntroductionINTRODUCTION1Thank you for selecting the Martin MX-4. This automated moving-mirror spotlightprovides 15 full and 2 split colors, 19 gobos

Introduction5• Do not stare directly into the light. Never look at an exposed lamp while it is lit. • Replace the lamp if it becomes defective or worn

6AC powerAC POWER2The MX-4 power supply has 5 voltage and 2 frequency settings. The factory defaultsetting is shown on the serial number label. Warnin

AC power7To rewire the power supplyAlways use the setting that most closely matches the local AC mains voltage andfrequency.1 Disconnect the fixture f

8AC power3 To set the frequency, move the black wire on the ballast to the “230-50” (50 Hz)or “230-60” (60 Hz) terminal as shown. The wire is released

Installation9INSTALLATION3The MX-4 can be fastened directly to a suitable surface or to a rigging clamp bymeans of its adjustable mounting bracket. It