Martin MAC 250 ENTOUR Manual de usuario descargar pdf

MAC 250 Beam Installation Note 1

MAC 250™ Beam Kit

Installation Guide

Introduction

This Installation Guide explains how to install the MAC 250 Beam™ Upgrade Kit to convert a standard

Martin Professional™ MAC 250 Wash™ to a MAC 250 Beam model. Installation only takes a few

minutes. A fixture software update is required if the installed software version is earlier than v. 1.4.0.

If you keep the standard components you remove, the MAC 250 Beam components can be uninstalled

and the fixture returned to standard MAC 250 Wash configuration at any time.

The MAC 250 Beam Kit has part number P/N 91610101.

For the latest documentation and information about this and all Martin Professional products, please

visit the Martin website at www.martin.com.

Warning! The MAC 250 Beam has a much more intense light beam than the standard MAC 250

Wash. Do not use it to illuminate any surface closer than 3.5 m (11 ft. 6 ins.) from the front of the

head, or you may create a fire risk.

Make sure that the front lens does not face the sun directly for longer than a few seconds at any

time during daylight hours. The Beam lens can focus the sun's rays inside the fixture, causing

internal damage and creating a possible fire risk.

Apart from the new minimum distance to illuminated surfaces specified above, follow all the

other safety precautions in the MAC 250 Wash user manual when installing the MAC 250 Beam

Kit and using the modified product. The user manual is supplied with MAC 250 Wash fixtures,

and the latest revision of the user manual is also available for download from the Product

Support page for the MAC 250 Wash at www.martin.com

Disconnect the fixture from power and allow to cool for at least 20 minutes before starting work.

The MAC 250 Beam Kit must be installed by qualified professional technicians only. Read all of

this Installation Guide carefully before starting to install the Kit.

If you have any questions about how to install the MAC 250 Beam Kit or use the MAC 250 Beam

safely, please contact your local Martin distributor (see www.martin.com/distributors for details)

or call the Martin 24-hour service hotline on +45 8740 0000, or in the USA on 1-888-tech-180.

Important! Do not get oil or grease onto optical components. If necessary, clean components

with 99.9% isopropyl alcohol.

Martin Professional A/S and all affiliated companies disclaim liability for any injury, damage, direct or indirect loss, consequential or

economic loss or any other loss occasioned by the use of, inability to use or reliance on the information contained in this installation note.

The Martin logo, the Martin name and all other trademarks in this document pertaining to services or products by Martin Professional A/S

or its affiliates and subsidiaries are trademarks owned or licensed by Martin Professional A/S or its affiliates or subsidiaries.

P/N 35000607 Rev. G

1 2 3 4 5 6 7 8

Indice de contenidos

Pagina 1 - Installation Guide

MAC 250 Beam Installation Note 1MAC 250™ Beam KitInstallation GuideIntroductionThis Installation Guide explains how to install the MAC 250 Beam™ Upgr

Pagina 2 - Installation procedure

MAC 250 Beam Installation Note 2OverviewThe MAC 250 Beam Upgrade Kit contains the following items:• MAC 250 Beam front lens assembly, P/N 62409076• M

Pagina 3 - Figure 5

MAC 250 Beam Installation Note 35. See Figure 3. Fasten the new front lens mounting bracket (P/N 62420240) supplied in the Kit to the front of the he

Pagina 4 - Figure 7

MAC 250 Beam Installation Note 47. A set of six beam effect gobos (P/N 62420250) is supplied in the Kit. See Figure 6. To install a beam effect gobo,

Pagina 5 - Figure 10

MAC 250 Beam Installation Note 512. See Figure 9. Clip the new front lens assembly securely onto its mounting bracket in the front of the head.13. St

Pagina 6 - Appendix A: MAC 250 Beam

MAC 250 Beam Installation Note 6Appendix A: MAC 250 Beam recommended gobo positions1. Beam aperture 152. Beam aperture 103. Beam 2 dots4. Beam 3 dots

Pagina 7 - Control menu

MAC 250 Beam Installation Note 7Appendix B: Changes in controlControl menuWhen the MAC 250 Beam Kit is installed iun a MAC 250 Wash, the control menu

Pagina 8

MAC 250 Beam Installation Note 8Martin Professional A/S • Olof Palmes Allé 18 • 8200 Aarhus N • DenmarkTel: +45 8740 0000 • Fax +45 8740 0010 • www.m

Mas documentos para Controladores de dj Martin MAC 250 ENTOUR

a Ver el documento Martin MAC 250 ENTOUR Manual de usuario

Martin MAC 250 ENTOUR Manual de usuario (49 paginas)

Martin MAC 250 ENTOUR Manual de usuario (40 paginas)

Comentarios a estos manuales

Sin comentarios

Martin MAC 250 ENTOUR Manual de usuario

Busca en linea o descarga Manual de usuario para Controladores de dj Martin MAC 250 ENTOUR. MAC 250™ Beam Kit Installation Guide Manual de usuario

Indice de contenidos

Mas documentos para Controladores de dj Martin MAC 250 ENTOUR

Comentarios a estos manuales

Relacionado con productos y manuales para Controladores de dj Martin MAC 250 ENTOUR